Linksys PAP2 Device

demo

Linksys         PAP2-NA Phone Adapter

reset         linksys PAP2 phone adapter , linksys phone adapter , linksys PAP2 phone adapter , phone adapter configuration instructions         , phone adapter configuration , linksys IP address , reset linksys PAP2 phone adapter , linksys PAP2 phone device

The Linksys PAP2 is a fully functional 2 port analogue telephone adapter which can be used with VoIP services.         Like all ATAs, the Linksys PAP2 device plugs into your DSL router ( broadband router ) and phone ( corded phone or cordless         phone ), and you can make and receive phone calls without using your computer ( your computer is switched off ). Plus 2 phones         in, one into each port, and you can have 2 independent VoIP lines!

The benefits of         Linksys PAP2 and linksys PAP2T - Phone Adaptor from Linksys

• Multi Lines with the ability of supporting two VoIP lines. The Linksys PAP2T can connect up to two         phone lines through your high speed cable or DSL Internet connection.
  
• Easy to set         up, easy to use if you already have a DSL router. Just plug it into your broadband connected router and the power supply,         use the two standard telephone jacks to connect your phones, wired or cordless. Pick up the phone, hear the dial tone and         ready to make calls.
• Convenience: with its small size, you can bring it with you when tralveling         anywhere. When you want to use the phone device in other location - anywhere in the world - just disconnect the phone device         and take it to other location, simply plug it into any broadband Internet connection. Connect a phone and you can make and         receive calls.
  

Linksys PAP2 Set-Up         Instructions

Reset         Linksys PAP2 phone adapter

Here is instruction on how to reset linksys PAP2 phone adapter to factory default:         ( in case you don't know password )

• From phone which connected         to Linksys PAP2 phone adapter, dial  ****73738#
  
• if it asks for password, use 8995523# or 7756112# or 5465866# or 50274537# or         78196365# (One of these numbers should work for you)
  
• enter 1 to confirm, press #,
  
• Hang up.
  
• To check your Linksys PAP2's IP: Pick up the phone ( connected to Linksys PAP2 phone adapter )         dial  ****110# The voice will tell current IP (example: 192.168.1.103). Now you can get into PAP2 setup pages without         password. In address bar of your internet browser type http://192.168.1.103/admin/advance (I use the same example) Press Enter.
  

• Other helps in case you don't know user name or password:
  
  

                                    try         user name : user

                                                 Password: 1234

Linksys PAP2-NA Phone Adapter Configuration Instructions
Linksys PAP2-NA Phone Adapter Configuration Instructions: The Linksys Phone Adapter enables use of high-quality         feature-rich telephone service through your cable or DSL Internet connection. Just plug it into your home Router or Gateway         and use the two standard telephone jacks to connect your existing phones. Each phone jack operates independently, with separate         phone service and phone numbers -- like having two phone lines, you'll get clear telephone reception, even while using         the Internet at the same time for normal data operations. Here are steps for phone adapter configuration:

STEP 1
You must first determine what IP address it received. To do this, you need to pick         up the phone attached to the Line 1 jack ( of  linksys PAP2 phone device )

• dial: ****         (four asterisks)
• hear "linksys         configuration menu"
• then dial: 110         #
• and you will be told the IP address of your device (e.g. 192.168.0.100).
  

STEP 2
Go to browser on any computer on your network and enter the address:

http://<IP ADDRESS>/

Replace <IP ADDRESS> by         the address that was given to you in STEP 1.

STEP 3
Click on the "Admin Login"         button near the top right side of the screen, then click on the "Line 1" tab.

STEP 4
Modify a few parameters from the factory default. They are:

• Proxy: sip.inphonex.com
• Display         Name: Enter your full name, this will show up as part of your caller id.
• User ID: Enter the         phone number you chose when you signed up for InPhonex service.
• Password: Enter the password         that you chose when you signed up for InPhonex service.
• Register Expires: 3600
  

STEP 5
Save bandwidth: change Line 1 "Preferred Codec" to G729a.

Also change the "Use Pref Codec Only" to No.

You can only do this for one line. So, if Line 1 is on G.729a, Line 2 has to be some         other codecs.

STEP 6
Save settings. Click on the "Save Settings " button         at the bottom of the form.

STEP 7
Done - Ready to make calls!

From: www.phonecallcheap.com

demo

If incoming calls does not ring

When someone calls this         number ( connected to Linksys PAP2 device ) the phone ( connected to Linksys PAP2 device ) does not ring, although         if you pick up the phone, the connection is working good and the sound is clear. When you call from this phone ( connected         to PAP2 device ) to any phone, the people who receive your call can hear the ring.

When someone calls this number ( connected to Linksys PAP2 device ) the phone ( connected to Linksys         PAP2 device ) does not ring, although if you pick up the phone, the connection is working good and the sound is clear.         When you call from this phone ( connected to PAP2 device ) to any phone, the people who receive your call can hear the ring.

When someone calls this number ( connected to Linksys PAP2 device ) the phone ( connected         to Linksys PAP2 device ) does not ring, although if you pick up the phone, the connection is working good and the sound         is clear. When you call from this phone ( connected to PAP2 device ) to any phone, the people who receive your call can hear         the ring.

Solution         1:

Check         ON-OFF button of your phone ( the phone which connects to Linksys PAP2 device ) - Make sure it turns ON

If the phone set has a bad ring, replace         by a good phone set.

Note:
PAP2 is NOT working         well with a digital phone since it may encounter some problems. It must be a analog phone to work good with the         PAP2 device.

If you are using cordless phone - Not all cordless         phones are quite compatible with VoIP, although many of them will work good for incoming calls and out coming calls but         can not ring with incoming calls. Make sure to choose the one which works with Linksys PAP2 devices. All ANALOG CORDLESS PHONE         models with 2.4 GHz to 5.8 GHz, 900 MHz should work good with VOIP services.

Solution         2:
If you are using ROUTER - check the ROUTER. The router which         connects between ADSL (Modem/Jack/Filter...) and Linksys phone device must be working good.

ADSL(Modem/Jack/Filter)         -->ROUTER--> LINKSYS PAP2-->PHONE

The router must be in good condition

Solution 3:
If you are using a router,  you         might need to do port forward. This issue is usually caused when the router         doesn’t send the traffic back. It can be resolved by configuring your router to allow Internet access to the device,         and to force a forwarding of any relevant data to it.
This is done by setting the router to route traffic in specific         ports we use, to the unique IP address the device uses in your local network.

How         to fix: all you to do is open the ports in the DSL router. In the         DSL router, need to change forward port 80 to the PAP2 LAN IP which requires for the remote router to be remote configure         enabled. No changes need to be made in the PAP2 Linsys Device.

For full instructions please refer router’s Manual Guide or consult with its         manufacturer. Instructions for specific routers can be found at .

Solution 4:

You might need to change Ring Waveform from Linksys device.

Change Ring Waveform from Sinusoid to trapezoid.

Log into Admin by typing the IP address into browser

Go to Advanced View

Click on REGIONAL tab

Select Trapezoid

(Change         the Ring Waveform from Sinusoid to Trapezoid)
Change the Ring Frequency from 25 to 20 (20 is the true specification for         North America).

Click Save and Exit

If issue still persists, increase the Ring Voltage to 90.

When someone         calls this number ( connected to Linksys PAP2 device ) the phone ( connected to Linksys PAP2 device ) does         not ring, although if you pick up the phone, the connection is working good and the sound is clear. When you call from this         phone ( connected to PAP2 device ) to any phone, the people who receive your call can hear the ring.

Test

Configuring the Linksys PAP2T is a relatively simple task.  Here are the steps to get you up and running.
Table of contents

• Physical Connections
• Using the ATA's Voice Menu
• Basic Browser Configuration
• Advanced Configuration Options: Ring Voltage
• Advanced Configuration: Dial Plan
  

Physical Connections

• Connect the ATA to power making sure to use a 5V power adapter.  Connecting 12V to the ATA will damage the equipment.
• Connect the ATA port labeled Internet to your network with an ethernet cable. Make sure the ethernet cable has been tested and that a computer can acces the internet using the same cable and switch port to be used for the ATA.
• Connect a telephone to the port labeled Phone 1 on the ATA
  

Using the ATA's Voice Menu
We find it's best to configure ATAs with static IP addresses, even in DHCP networks so it's easy to find their configuration pages if you need to make changes later. The Linksys ATA, though, comes configured to look for DHCP out of the box. You'll need to use the phone's voice menu to turn off DHCP and set an address. If you will have multiple ATAs, it can be convenient to group all the ATAs together in a similar address range, for example between 192.168.100.50 and 192.168.100.60.

• Pick an IP address on your network that you know is unused.
• Pick up the phone and dial **** to access the ATA's voice menu
• Dial 100# to check the status of DHCP on the ATA, it will probably say "Enabled"
• Dial 101# to change the DHCP setting, the ATA will say "Enter value..."
• Dial 0# to set DCHP to disabled, the phone will say "Press 1 to Save..."
• Dial 1 to save the setting
• The ATA should return to the main voice menu.  If it did not, hang up, pick up the phone, and dial **** again.
• Dial 111# to set a static IP address.
• Dial the IP address chosen in step 1, using * for dots and ending with a #.  For example, if the IP address was 192.168.100.51, dial 192*168*100*51#
• Dial 1 to save the IP address.
• At the ATA main voice menu, dial 110# to check that the IP address was properly stored.  The ATA should read back the IP address.  (Note,
  the ATA must be physically connected to a network with an ethernet cable...if no ethernet
  cable is connected to the ATA, it will always read 0.0.0.0 for the IP
  address
• Hang up the phone.
• Try to ping the ATA's IP address from another computer on the same network.  If the ATA is pingable, continue to the next step.  If the ATA is not pingable, repeat steps 2-12 to check settings until the ATA is reachable by ping.
  

Basic Browser Configuration
Now that the phone has an IP address, the rest of the configuration can be done from a browser on a computer on the same network.  Inveneo recommends Firefox.

• Open your web browser and connect to the IP address set for the ATA above. The browser should display the Linksys PAP2 configuration screen.
  The Linksys PAP2T Configuration Interface
• In the upper right corner, click "Admin Login"
• Click the "System" tab near the top of the screen
• Fill in the same settings for the ATA that you would use when configuring any other computer for the network.  The gateway, net mask, primary DNS, and (if necessary) secondary DNS field should be completed.
  Linksys PAP2T basic network settings
• Click "Save settings" Near the bottom of the page
• The text "Please wait while the PAP2 updates its settings..." will display for a few seconds, and then the browser should return to the info page of the Linksys configuration.
• Click the "Line 1" tab
• For proxy, enter the IP address of the Inveneo IHL server or other VOIP server being used to provide VOIP service.
• Make sure register is set to yes
• To continue beyond this step, a VOIP extension with username and password must have been created on the VOIP server providing service to this ATA.  One VOIP account must be created for each ATA or VOIP device in the network
• Set both display name and username to the VOIP username for this ATA.  If configuring for an Inveneo IHL server or other Asterisk server, the username and display name will be the extension number (not the extension name) created for this ATA.
• For password, enter the password for the VOIP account for this ATA.
• Scroll to the bottom of the page and click Save Settings
• The browser should again return to the main page of the Linksys configuration screen
• In the "Line 1 Status" section of the status screen the
  "Registration State" field should read Online. If the ATA shows its status as online it has successfully connected to the VOIP server.  If it shows "Registration state: offline" repeat steps 1-14 and check settings.
  Linksys PAP2T Registration Status
• Pick up the phone, a dial tone should now be present on the line.
• Dial one of the extensions in the network, test that the phone rings, and check the voice quality
• Hang up the phone.
  

The ATA is now configured. Depending on network bandwidth, it may be necessary to adjust VOIP codec settings.The default u711 voice codec is high quality, high bandwidth, and works well over high bandwidth, long range wifi links. If connecting over the internet, higher compression codecs will be required.

Advanced Configuration Options: Ring Voltage
ATA configuration is complete, but there are a few additional settings that may be necessary depending on equipment and deployment specifics. In particular, if the VOIP works properly when dialing but the ringer does not ring when the ATA receives incoming calls, the following steps will be necessary. Analog telephones ring by sensing a voltage sent down the phone line. Phones from different countries require different settings in this area to function properly.

• Near the top of the configuration screen, click "Switch to Advanced View"
• Click the "Regional" tab of the configuration screen
• Scroll most of the way down the page to the "Ring and Call Waiting Tone Spec" settings.
  Linksys PAP2T Ring Voltage Settings
• Two common settings are displayed below. Choose the one that matches your equipment, or adjust as necessary.
  

  	Ring Waveform	Ring Frequency	Ring Voltage
  United States	Trapezoid	25 Hz	80 V
  United Kingdom	Sinusoid	20 Hz	85 V

• Scroll all the way to the bottom of the page and click "Save Settings"
  

Inveneo has found that the Trapezoid waveform setting works better with newer, digital compatible phones, while the sinusoid setting works better with the older equipment often found in developing regions.  The default US settings will work in most cases, particularly across Africa.  The UK settings may be particularly useful in South Asian countries like Nepal and India.

Advanced Configuration: Dial Plan
It is always possible to tell the ATA to dial a number immediately by dialing a # after the last digit. However, most users will want the ATA to dial automatically once a complete number is received For this to happen, the ATA must be told a series of rules to use to recognize complete phone numbers for dialing. This set of rules is called a dial plan.

• Scroll to the bottom of the page and find the "Dial Plan" section
• Enter a dial plan that matches the dial plan on the VOIP server in use:
  
  • Separate different match patterns with |
  • Use the wildcard x to match any single digit
  • Use the wildcard . to represent a group of digits of any length.
  • Specify digit ranges from m to n using [m-n]
    
  The example dialplan ([2-8]xxx|9xxxxx.)is designed to expect any 4 digit extension beginning with any number between 2 and 8 or any number longer than 6 digits beginning with 9.
• Scroll all the way to the bottom of the page and click "Save Settings"
  

Test

demo 发表于 2013-1-15 09:52
If incoming calls does not ring When someone calls this         number ( connected to Li ...

Re: No ring at my PAP2T when incoming calls ocurr  Options  ‎11-14-2006  01:22 AM
What version of firmware has your voip adapter? When I bought my pap2t, it had 3.1.9. I had the same problem. Phone didn't ring. I flashed my adapter with 3.1.15 and my problem disappear.                                                                                      .........................
The previous poster is correct in that flashing to the current firmware does fix the problem. However, if that is not an option just do the following. This requires the "admin" password. If your device is locked by the VoIP provider you cannot do this on your own.

Open the web administration page
Click on "admin" and provide the password if required
Click on "switch to advanced view"
Click on the Regional tab
Scroll down to the section labeled "Ring and Call Waiting Tone Spec"
The settings you want are located here.. make the necessary changes and scroll to the bottom and click on "save settings".